Quick Link II Fax  (250-3027B)     Error Codes         Faxback Doc. # 3245

In the unlikely event of a fax not successfully transmitting, the Fax Logs
will display an error code.  You may get a detailed explanation of the
error by clicking the ERRORS button when displaying the INFO on the Fax
Log entry, or from the Help system.  The following is a summary of the
Error Codes:

Error Codes:

    100 - 199    Modem Errors

    200 - 299    File Errors

    300 - 399    Send Fax Errors

    400 - 499    Receive Fax Errors

    500 - 599    Miscellaneous Errors

Modem Errors:

    Error: 101   Unable to open COM port.

    Error: 102   Unable to detect modem.

    Error: 103   Modem not a fax modem.

File Errors:

    Error: 201   Unable to create necessary file.

    Error: 202   Out of disk space.

    Error: 203   Error reading file.

    Error: 204   Error writing file.

    Error: 205   Unable to close file.

    Error: 206   Unable to access file.

    Error: 207   Unable to open fax file.

    Error: 208   Unable to open exchange file.

    Error: 209   Unable to open setup file.

    Error: 210   Unable to create/send cover page.

    Error: 211   Unable to create/send headers.

    Error: 212   Unable to open file.

    Error: 213   Error reading exchange file.

Send Fax Errors:

    Error: 301   No dial tone detected from modem.

    Error: 302   Number dialed was not a fax machine.

    Error: 303   Number dialed was busy.

    Error: 304   No carrier detected after dial.

    Error: 305   Error occurred during fax training.

    Error: 306   No CONNECT message from remote.

    Error: 307   No End Of Page acknowledgement received.

    Error: 308   No phase D page response received.

    Error: 309   Unknown phase D error.

    Error: 310   No End Of Page response received.

    Error: 399   Unknown send error.

Receive Fax Errors:

    Error: 401   Remote fax failed to train.

    Error: 402   Remote fax failed to train.

    Error: 403   Error during End of Fax handshake.

    Error: 404   Error occurred during End Of Page.

    Error: 405   Unknown phase D error.

    Error: 406   Received no acknowledgement during End Of Page.

    Error: 407   Time-out on end of reception.

    Error: 408   No end of transmission acknowledgement received.

    Error: 499   Unknown fax receiving error.

Miscellaneous Errors:

    Error: 501   Unable to allocate memory.

    Error: 502   The selected document contains 0 pages.

AT command set

Most modems used with PC's implement the AT Command Set as a method of
issuing commands to the modem.  The actual implementation by your modem's
manufacturer is documented in the hardware manual included with your
modem.  The chart below is a summary of many of the more commonly used AT
commands.  Many users may never find a need to use this command set, as
Quick Link II Fax does much of the work for you.

    Command     Description

    AT          Attention command and precedes command line

    A/          Repeat preceding Command

    A           Answer call immediately

    DT          Dial Touch Tone Mode

    DP          Dial Pulse Mode

    E           Command Echo Disabled

    E1          Command Echo Enabled

    H           Hangup (on-hook)

    H1          Off Hook

    I           Output Product Code to PC

    L           Speaker Volume (L0, L1, L2, L3)

    M0          Speaker off

    M1          Speaker on until Carrier Detect

    M2          Speaker always on

    M3          Speaker on from dial to Carrier Detect

    O           Return to On-line Communications

    O1          Return to On-line Communications & Retrain

    Q           Send Result Code Messages

    Q1          Do not Send Result Code Messages

    Sr?         Read & Display Contents of Register (r)

    Sr=n        Set Register (r) to Value (n), ATS0=1, answer phone on
                first ring

    V           Result Code Messages sent in Numeric format

    V1          Result Code Messages Sent in English Word Format

    X           Extended Status Mode

    Y           Long Space Disconnect

    Z           Reset and Initialize Modem

    +++         Escape Code from On-line to Command State

(br/all-10/11/94)